Size master Automatic penis pump

Who is this penis pump best for?
This automatic peis pump is a good choice for anyone who wants pumping to feel simple and predictable.
Beginners will like the clear levels and easy buttons, while more experienced pumpers will enjoy the steady automatic pull.
It is also a nice fit if you enjoy watching the chamber and seeing the buildup happen in real time.

What does kPa mean?
kPa stands for kilopascal. It is simply a way to measure pressure.
With this pump, a lower number means a lighter vacuum, and a higher number means a stronger pull.
You do not need to remember the science behind it - just think of the 5 levels as steps: 10 kPa is the gentlest, 20 and 30 kPa feel more noticeable, and 40 and 50 kPa create the firmest suction.
Always use the lowest level that feels good.

How do I use this automatic penis pump?
1. Charge it. Fully charge the pump, then unplug it before use.
2. Put it together. Attach the clear chamber to the powered top and place the silicone seal into the open end.
3. Check the fit. Make sure your penis fits comfortably through the silicone opening and inside the 7 1/2-inch chamber.
4. Add lubricant. Apply water-based lubricant around the seal and your penis.
5. Insert slowly. Guide your penis through the seal and press the base of the chamber evenly against your body.
6. Start at 10 kPa. Turn the pump on and begin with the lowest level.
7. Move up slowly. Press + only when you want more pressure. Use - whenever you want less.
8. Release before removing. Hold the VALVES button until the pressure is gone, then take the pump off gently.

How can I make the pumping session feel more sensual?
1. Warm up first with your hand, a vibrator, or a partner's touch.
2. Once you are partly erect, slide into the chamber and stay on the first level for a while instead of rushing upward.
3. The slow buildup can feel more teasing, and the clear tube gives you or a partner something tempting to watch.
4. You can also pause between level changes and enjoy the heavy, full feeling before adding more pressure.

What should I do if the penis pump will not hold suction?
Check that the silicone ring is sitting flat and has not folded.
Add a little more water-based lubricant around the opening, then press the chamber evenly against your body.
Body hair or a loose seal can also let air in.
Do not move to a higher level just to fix a leak - reposition the seal first.

What if the silicone ring feels too tight?
Stretch the opening gently with your fingers before use and add more water-based lubricant.
Insert slowly instead of letting the pump pull you in. If the ring still feels painful, pinchy, numb, or hard to remove, stop.
The seal should feel snug, not restrictive.

When should I lower or release the pressure?
Press "-" whenever the pull starts to feel too strong.
Hold the VALVES button right away if you feel pain, sharp pinching, numbness, coldness, strong discoloration, trapped skin, or swelling that worries you.
Pumping should feel firm and even, not painful.

How long should I use this penis pump?
Keep your first sessions short and release the pressure often so you can check how your body feels.
Your penis should stay warm, comfortable, and normally colored.
Never fall asleep while using the pump, and do not use it while too distracted or intoxicated to notice discomfort.
Speak with a healthcare professional before use if you take blood thinners or have concerns about circulation, bleeding, penile health, or heart health.

Which lubricant should I use with this penis pump?
Use EdenFantasys water-based lubricant around your penis and the silicone seal.
It helps the ring glide more comfortably and can improve the seal.
Add more if the opening starts to feel sticky.
Avoid silicone-based lubricant since it's unsafe for the silicone ring.

How do I clean and store this automatic penis pump?
1. Turn the pump off and release all pressure.
2. Remove the silicone ring and clear chamber from the powered top.
3. Wash the removable ring and chamber with warm water and mild soap or EdenFantasys Toy Cleaner.
4. Wipe the powered part with a lightly damp cloth. Do not place it under water.
5. Let every part dry fully before putting the pump back together.
6. Store it in a cool, dry place where the clear chamber will not get scratched.