Fun but Crooked Cocks be careful
The Clone a Willy is fun to make and a great gift. At the very least, your penis becomes immortalized.Published: April 10, 2009
Pros:
Easy to make, fun surprise, great gift.
Cons:
Vibrator is kinda large, slightly difficult to insert in the middle if your dick is crooked.
This was really fun to make. It felt really good when I inserting myself into the molding clay, warm, and oozing. Because it felt so good, my dick was in its extra firm and rigid state. So now I have created an extra hard, and large version of my penis for my wife to use, or for me to use on her.
I used a cock ring near the base of my penis. This created some extra bumps for the deeper penetration, and also gave the clone some grip for my hand or her hand to grab on to when inserting into the various places it likes to go.
When inserting the vibrator after, I needed to be careful to find the center. I'm a little crooked so the vibrator ended up closer to one side of the clone than the other. We've since taken the vibrator out, the hollow inside makes it so the clone can have more flex if we need it. I'd suggest using the vibe as a stand alone and just create a solid dildo if your penis is really crooked. You should also be careful when you stick it in the mold because if your touching the side of the container you might end up with a flatter side to your clone.
I made it as a surprise for my wife. She uses it solo sometimes when I'm away, but also likes to just take it out to hold and look at when she knows the real thing is cumming home soon. I have used it on her vaginally and anally while giving her oral. Also, now I can enjoy being able to penetrate her while I receive oral. But most of all my wife can now enjoy getting Double Penetration from two identical dicks of me!
I used a cock ring near the base of my penis. This created some extra bumps for the deeper penetration, and also gave the clone some grip for my hand or her hand to grab on to when inserting into the various places it likes to go.
When inserting the vibrator after, I needed to be careful to find the center. I'm a little crooked so the vibrator ended up closer to one side of the clone than the other. We've since taken the vibrator out, the hollow inside makes it so the clone can have more flex if we need it. I'd suggest using the vibe as a stand alone and just create a solid dildo if your penis is really crooked. You should also be careful when you stick it in the mold because if your touching the side of the container you might end up with a flatter side to your clone.
I made it as a surprise for my wife. She uses it solo sometimes when I'm away, but also likes to just take it out to hold and look at when she knows the real thing is cumming home soon. I have used it on her vaginally and anally while giving her oral. Also, now I can enjoy being able to penetrate her while I receive oral. But most of all my wife can now enjoy getting Double Penetration from two identical dicks of me!
This content is the opinion of the submitting contributor and is not endorsed by EdenFantasys.com
About author
Forum
-
Clone-a-willy construction!
-
I read a review where a man made a few of these single-handedly (hats off!). Instead of just placing the plastic tube over his penis, he cut off the closed end of the tube, sat down leaning back and poured in the mold, making sure it covered his entire length.
This actually seems to make more sense, provided you protect whatever it is you're sitting on, as there might be less fumbling about with timing and overflow of contents.
Has anyone tried it this way with more success? Any opinions? I read a review where a man made a few of these single-handedly (hats off!). Instead of just placing the plastic tube over his penis, he cut off the closed end of the tube, sat down leaning back and poured in the mold, making sure it covered his entire length.
This actually seems to make more sense, provided you protect whatever it is you're sitting on, as there might be less fumbling about with timing and overflow of contents.
Has anyone tried it this way with more success? Any opinions? :) -
Quote: I read a review where a man made a few of these single-handedly (hats off!). Instead of just placing the plastic tube over his penis, he cut off the closed end of the tube, sat down leaning back and poured in the mold, making sure it covered his entire length.We had one, and used the tube. My hubby is rather "gifted" in his length as well as girth, so in some parts of the dildo, the material was very thin near the bullet. I would suggest that if you do do one, don't put the bullet in.
This actually seems to make more sense, provided you protect whatever it is you're sitting on, as there might be less fumbling about with timing and overflow of contents.
Has anyone tried it this way with more success? Any opinions? I read a review where a man made a few of these single-handedly (hats off!). Instead of just placing the plastic tube over his penis, he cut off the closed end of the tube, sat down leaning back and poured in the mold, making sure it covered his entire length.
This actually seems to make more sense, provided you protect whatever it is you're sitting on, as there might be less fumbling about with timing and overflow of contents.
Has anyone tried it this way with more success? Any opinions? :) -
Hmmm, this is interesting. My boyfriend and I want to get this and the only thing we're worried about is that it won't work properly and we'll have to buy another one. This seems like a good technique. We'll try it out and I'll let you know :)
18 posts Read all -
Thank you for viewing Clone-a-willy kit – molding kit review page!
Great first review! Welcome to the community!
When you finished cloning, did you have to wash up? Was there residue? What do you think of the material quality of the resulting toy? Did you and your wife choose to use a condom on the toy when using it for penetration?
What a perfectly lovely idea...being fucked by your partner's "twin"! So many wicked scenarios you could work that into, LOL. Seriously though how hard was this thing to work with? What material was the resulting dildo/vibe? I'm assuming rubber, did it have a nasty smell? Still it sounds fun, glad to hear it was a success for you and your lady.
Welcome to the community!
~Nice Review